3 Easy And Affordable Ways To Refinish Your Hardwood Floors

You can see how we prepped a new home for these California transplants. We also provided interior painting and floor refinishing for this entire Madison, NJ home prior to moving day. Our team is experienced in hardwood floor repair and is ready to restore your hardwood floors back to their original beauty. For example, some flooring businesses may be able to sand approximately 1,500 to 2,000 square feet in one day or several hundred square feet in a few hours. Re-sanding floors with old finishes will usually take longer than sanding unfinished hardwood.

It might also take longer to sand floors in older homes, floors that have sustained water damage or floors located in humid environments. There are a few things to take into consideration when wanting to know how much it will cost to refinish or resurface your wood flooring. Penetrating oils—there are several types, but tung oil is the most common—soak into the wood’s pores, helping prevent scratches and other damage.

Wipe down the floor with a damp rag to remove all debris and dust. Typically, a professional will charge anywhere from $3 to $4 per square foot to refinish floors. For a 2,000-square-foot house, that can mean a bill as high as $8,000. It is possible to complete an entire 2,000-square-foot home in as little as four days for about $700. Follow these steps to refinish hardwood floors with a professional quality result. This service is also referred to as a “maintenance coat” and is meant for homeowners who need an additional layer of protection on their hardwood.

Use the same grit sandpaper on the edge sander to sand right up to the wall . Sand using the 40-grit sandpaper until the floor color is completely uniform. Once the finish is roughed up, we put on a water-based polyurethane, which can be recoated in 3 hours. Oil-based polys are cheaper, but each coat takes about 8 hours to dry. With either finish, we recommend a fresh coat every two years or whenever the floor looks worn.

For best results, use two stain colors to match the light and dark patterns in the wood grain . Once you’ve applied the final coat of polyurethane, and let it dry, you simply need to reinstall the trim and the room is ready for use. If you’re using oil-based products, it’s recommended to use at least two coats, and at least three for water-based options. In terms of application, each has pros and cons as well. Water-based products, for example, are thinner, so they will naturally go on more evenly and dry quickly.

Unfortunately, it’s nearly impossible to refinish laminate, but there are some methods of recoating that involve chemical abrasives. These methods are a long shot, however, and are not recommended by the flooring experts at The Good Guys. After you’ve sanded down to bare wood, fill any cracks with color-matched wood filler. Apply the stain and allow to dry thoroughly before applying two to three coats of finish. If scratches and wear are only on the surface finish and the wood underneath is in good shape, you can restore the topcoat by buffing, a process also called screening. Always wear a good dust mask or respirator, ear protection, and goggles.

From refinishing and resurfacing to a variety of stain colors, you can choose from a variety of options to enhance the beauty of your home. After floor cleaning, douse the problem areas with mineral spirits to darken them. It’s better to utilize two different stain colors to match the grain of the hardwood better. It usually takes at least 24 hours before the furniture pieces can be brought inside without damaging the new finish. Clean the floor with a gallon of water mixed with two tablespoons of dishwashing liquid. Make sure that the mop you are using is only slightly damp to prevent causing water damage to the floors.

Polyurethane is now the most common topcoat finish for hardwood floors. A clear, almost plastic-like substance, polyurethane is applied with a standard paintbrush and is available in a variety of finishes, from matte to glossy. Its purpose is to create a clear, protective layer over the top of the wood that resists stains and scratches. Once you have completed sanding the floor using power tools, you can work on any areas that remain, using medium-grade sandpaper. This can also help to smooth out any rough patches that may have occurred during the process.

Leave a Reply